The 24-foot bandsaw I’d been running for a little over a year finally went quiet on a Friday.
I was working for an oil services company. We made components for deep-sea wells. I was a saw operator there, cutting heavy pipe on a bandsaw that would eventually be machined down into various parts. Then the Great Recession hit, and the economy started sliding.
We went through several rounds of layoffs. I dodged the first one, the second, and the third. When the fourth round rolled around, my number came up. I was laid off.
For months, maybe a year or a little more, I scraped to find work. It was dead silence everywhere. When I did land an interview, the room was packed with guys in their late 30s and 40s, workers with decades on the line. I lived in a manufacturing town, so when one plant laid off, the seasoned hands flooded to the next. Every opening I applied for had a line of veterans out the door. Eventually, I caught a break and landed a steady temp spot at a local foundry.
As a janitor.
The posting in the break room
I came in on second shift, cleaning the plant, scrubbing restrooms, taking out trash. Standard temp janitorial work alongside a few other people. I didn’t hate it. It had a steady schedule, no drama, and after a year of uncertainty, a paycheck was a paycheck. Eventually, the company hired me on full-time.
Part of my routine was cleaning the administrative offices. The HR director happened to be the one I reported to.
One afternoon, sitting in the break room, I saw an internal job posting: Furnace Operator.
It caught my eye immediately. I’d already been a machine operator on the bandsaw at an oil services company. Operating a furnace sounded fire, literally and figuratively. Metal and real machinery again.
I stopped by the HR director’s office while emptying the trash and asked about it. She told me to apply. A day later, the plant manager walked me around the top deck, showed me the setup, and talked through the work. The next day, HR called me in.
“You’re always on time,” she told me. “You always show up, and you have a good attitude. The plant manager says he’s good with you.”
I got the job. Second-shift furnace operator. Better pay, a bigger challenge, and the kind of work I’d been missing.
2,500 degrees and a chipping gun
I showed up that next Monday ready to go. In my head, “furnace operator” meant sitting behind tinted glass in an air-conditioned booth, monitoring digital gauges, and punching buttons.
That fantasy lasted about ten minutes.
The first few days were a blur. An experienced operator walked me through it, but the expectation was clear: I’d be running this deck solo before long. We worked on what they called the “top deck,” the foundry’s second floor, elevated a full story above the main floor below.
Up there sat three massive holding furnaces containing tens of thousands of pounds of molten iron at 2,400 to 2,500 degrees.
Because the production guys down below couldn’t pour directly from those giants, we had to tap the holding furnaces into a “tundish,” a massive bowl with a pouring spout, which fed into long refractory trenches called “launders” that drained down to the floor-level furnaces.
Before any of that could happen, we had to preheat the ladles on the production floor below. Natural gas lines ran all across the foundry, up to the top deck and down to where the ladles sat. The lines were everywhere. You’d be feeding gas to a ladle and the whole time thinking about what would happen if one of those lines blew. But there was no other way. Preventing heat loss when the iron was poured was the name of the game.
After first shift wrapped, the launders and tundishes were caked with hardened slag and frozen iron.
My shift started with jackhammers and pneumatic chipping guns. Hours of vibration rattling through my wrists, beating dried slag off the runners.
Once cleared, we had to hand-pack refractory mud to rebuild the heat-worn trenches. Then remud and torch the launders themselves while balancing on the narrow catwalks that ran alongside them. There were catwalks for the tundishes but also sections of the launders.
Then we grabbed heavy impact guns to pound out the refractory material.
Then we moved to the forklift. I had to use it to position new ladles on the track, and these ladles were crazy heavy and liked to swing. The hard part was moving them smooth enough not to tip the forklift or send the load swaying into something it shouldn’t. One bad move with a ladle that size and you had a real problem on your hands.
Then came the chemistry. We had to take long glass tubes attached to rubber bulbs, dip them straight into the liquid iron to draw a quick vacuum sample, and let it instantly freeze solid. I’d sprint the slug down to the lab, wait for the breakdown, and run back up. Add 40 pounds of copper. Add manganese. We’d dump the raw minerals directly into the bath to dial in the spec.
For the bulk additions, we’d pick up pallets of minerals with the forklift, drive them up to the furnace, and open the lid. The margin for error was the distance between the forklift forks and a bath of liquid iron. Dumping those pallets was dangerous work, but when those minerals hit the bath and everything went up in flames, it’d get me pumped like hearing Welcome to the Jungle as I ran out onto a football field.
Part of prepping for production was getting as much slag off the top layer of the bath as I could. I’d turn the heat up in the furnace to make sure it held onto as much heat as possible, crack the lid, and balance on the catwalk with a long rake, scraping the slag off the surface and letting it fall into the pit below.
I should probably mention I have a fear of heights. Real helpful information to have after I’ve already been balancing over a pit for a couple of days.
By day two, my forearms and face were bright red. Not from the sun. From radiant heat off 2,500-degree iron, which we’d tapped at holding heat from the furnaces. The iron we poured was cast iron, the same stuff you’d find in old engines, manhole covers, and tractor buckets. Add a single drop of water to a pour, and the steam expansion alone would have launched molten metal thirty feet across the deck. A foundry rule I never forgot: never bring wet anything near the pour.
The catwalks connecting the furnaces were narrow metal paths with no railings. Just a straight 20-foot drop into the pit below, where pooled slag and stray iron sat waiting. One slip and you weren’t getting written up. You were crippled or dead. On the days I worked, when I sneezed, what came out was the color and thickness of used motor oil, the kind that pools under a car you’ve neglected. My lungs were working overtime just to clear the day.
Driving home that night, completely drained, sore, and cooked, only one thought bounced around my head: I want to quit. This sucks.
Make it to Friday
I didn’t quit. Instead, I made a deal with myself.
Just make it to Friday. Don’t worry about next month. Just get through the end of the week. If you get to Friday and you still can’t take it, walk away.
Friday came. I was exhausted, but I was still standing. I looked at myself in the mirror and thought, I can keep going.
So I went back the following Monday.
Gradually, the routine set in. My body adapted to the heat. I figured out how to handle the chipping gun without wrecking my shoulders. I got faster at packing refractory mud and nailing the mineral mixes. Eventually, I was running that deck completely alone, prepping the entire line and spending the last hour of my shift helping third shift kick off production.
The day the tundish blew
It wasn’t an easy place to stay long-term.
I was working with third shift one night, standing by Furnace 1 with a long rake, ready to pull slag out of the tundish as the pour started. They tapped the furnace. As soon as the molten iron hit the tundish, it blew.
The day before, I’d remudded that tundish, covered it with insulation, and put a torch in it to dry it out. Apparently it wasn’t enough. Either it got too cold overnight or someone snagged the torch before the moisture was gone. Either way, the tundish still held a lot of moisture, and when the iron hit, it flashed to steam. The whole thing went up.
There was nothing I could do but hold the back of my collar to keep slag from running down my neck. Iron was raining down everywhere. Then a chunk of iron and slag landed on my boot and began to melt through it. Within a split second I went from being set to rake slag to slipping out of my boots to keep my feet from melting.
I was in my early twenties. I decided right then I was too young to die working.
Calibrating what “hard” means
I’ve had plenty of stressful days, tough projects, and demanding jobs since that foundry.
Whenever things get chaotic, when deadlines loom, or when a role feels like a grind, I catch myself thinking, this is rough.
Then I stop.
I remember the tundish blowing up in my face. Iron raining down. My boots starting to melt.
And I think: well, it could be worse.
I could be back on the top deck.